Installing and using PPTP on Windows 95
Sean Quinlan
Last Updated: October 19th 1998
Introduction
Point-to-Point Tunneling Protocol (PPTP) is a
protocol that enables the Internet to be used as a replacement for the
long distance telephone network when remotely accessing the Bell Labs network.
For people that live far from the labs or are traveling, PPTP can greatly
reduce the cost of such access. PPTP also enables access over fast Internet
connections such as cable modems and DSL.
A typical scenario for using PPTP is as follows: A remote
user connects to the Internet via an Internet Service Provider (ISP) using
ISDN or a modem and establishes a connection to the PPTP server that is
attached to both the Internet and Bell Labs internal network. Once connected
to the server, network traffic is encapsulated in IP packets, set to the
server, and placed on the internal network. This tunneling of network
traffic is performed transparently. From the remote users point of view,
the remote computer is connected directly to Bell Labs network. The Internet
connection between the remote computer and the PPTP server is used as a
replacement for dialing directly into a modem connected to the internal
network.
This document describes how to install and use PPTP on
Windows 95.
Note, the instructions vary slightly for uses of Comcast cable modems.
Authentication
To use PPTP you will need to have a POP3 password on
the Brazil authentication server. If you have a Brazil account, you can
set your POP3 using the Brazil passwd command. If you do not have
a Brazil account, please see Irina Strizhevskaya (x7548).
Preparing your Windows 95 machine
Before you install PPTP, your Windows 95 machine should
be configure such that:
-
You can establish a connection to the Internet and successfully ping the
machine achille.cs.bell-labs.com. For
most users, this implies that you have a ISP account and you have configured
a Dial-up Connection. Alternatively, you may have a direct connection
to the Internet, for example, via an ethernet card connected to some external
LAN or a Comcast cable modem. (For Comcast users you must be able to ping
the machine at address 10.252.0.123)
-
If you plan to access Windows based resources on the internal network,
such as file servers and printers, you should enter a user name and password
when you start Windows 95. If Windows 95 does not prompt for a user name
and password when you boot your machine, you probably do not have Clients
for Microsoft Networks installed.
Installing PPTP client software
Windows 95 does not include the client software for using
PPTP, however, Microsoft provides this software, free of charge, as part
of the Dial-Up Networking 1.3 Upgrade (DUN 1.3). Before installing
the upgrade it is a good idea to have a Window 95 installation CD available
since you may be asked to insert the CD during the installation process.
Also, there have been reports of this upgrade interacting with the suspend/resume
modes of some notebook computers. Please let me know if you have problems
with this upgrade.
To upgrade your machine download and run the following
two executables.
| |
msdun13.exe |
upgrades Dial-Up Networking (DUN) to version 1.3 |
|
msdun13-128crypt.exe |
enables 128bit encryption for Dial-Up networking - must be installed
after DUN 1.3 |
More information about this upgrade can be found in
Microsoft Windows95 Dial-Up Networking 1.3
Upgrade Release Notes.
After installing the upgrade, it is a good idea to check that the dial-up
connection to your ISP still works.
Configuring a PPTP dial-up connection
PPTP enables the Internet to be uses as a substitute
for the phone network when making a dial-up connection; thus in Windows
95, you configure PPTP as a type of dial-up connection that uses a virtual
modem to dial into a matching virtual modem on the PPTP server. To create
such a dial-up connection:
-
From the Start menu, select Programs,
Accessories, then Dial-Up Networking. The Dial-Up Networking
window should appear.
-
Double click on Make New Connection.
-
Enter a connection name, such as "lucent". This name has no meaning
to Windows 95 and is simply a name for this configuration.
-
Select Microsoft VPN Adapter from the list of available modems.
This represents the virtual modem used to make a PPTP connection.
-
Press Next.
-
In the Host name or IP box, enter "achille.cs.bell-labs.com".
(Comcast users should enter "10.252.0.123")
-
Press Next, then Finish. A connection icon should appear
in the Dial-Up Networking folder with the name entered above.
-
Select with the right mouse button the connection icon just created, then
select Properties from the pop-up menu. The PPTP Server dialog box
appears.
-
Verify the information on the General tab.
-
Select the Server Types tab.
-
In the Advanced options box select the Log on to network,
Require encrypted password, Enable software compression, and
Require data encryption.
-
In the Allowed network protocols box, select TCP/IP and disable
NetBEUI and IPX/SPX.
-
Press the TCP/IP Setting button.
-
In the TCP/IP Settings dialog box, select Server assigned IP
address and Sever assigned name sever addresses.
-
Enable the Use IP header compression and Use default gateway
on remote network options.
-
Press OK .
-
Press OK .
Microsoft has designed Windows 95 in such a way that
the network performance over PPTP is intentionally limited. Users
of fast Internet connections, such as cable modems, can increase this limit
by configuring the two Dial-up Adapters in the Network Control Panel as
follows:
-
From the Start button, select Settings, then Control
Panel.
-
Double click on the Network icon.
-
Double click on the entry labeled Dial-up Adapter.
-
Select the Advanced tab, and click on the entry
labeled VPN media type.
-
Choose the Ethernet, ADSL, or Cable modem setting.
-
Press OK.
-
Double click on the entry labeled Dial-up Adapter
#2.
-
Select the Advanced tab, and click on the entry
labeled VPN media type.
-
Choose the Ethernet, ADSL, or Cable modem setting.
-
Press OK.
-
Press OK.
-
You will then be asked if you would like to reboot
the machine. Press Yes.
Connecting to the PPTP server
To connection to the PPTP server:
-
From the Start menu, select Programs, Accessories, then Dial-Up
Networking. The Dial-Up Networking window should appear.
-
If you are not connected to the Internet, double click the connection icon
for your ISP and establish the connection in the usual manner. After connecting
there should be a pair of modem lights displayed on the right hand side
of the status bar.
-
Double click the connection icon for the PPTP server, which is named lucent
if you followed the instructions above.
-
Enter your user name and password.
-
If you desire, you can check the Save passwd checkbox. This option
uses your Windows 95 login password to encrypt your PPTP password and save
it in the file system. As long as your Windows 95 password remains secret,
the saved password should be safe. Note that the password is only saved
after you have successfully connected.
-
Press the Connect button.
-
If all goes well, you should connect to the PPTP server, authenticate and
establish a connection. A pair of modem lights should appear on the status
bar.
To test the connection, open a MS-DOS window and type
"ping slocum.cs.bell-labs.com". If this succeeds
then you have successfully tunneled through the firewall and can access
the Bell Labs network. At this point you should be able to connect to resources
on the internal network using standard applications. One glitch is that
Windows 95 does not automatically append the common domain names such as
cs.bell-labs.com to DNS queries. This implies that you must enter full
addresses such as slocum.cs.bell-labs.com rather than just slocum
for some applications.
After successfully pinging slocum, try to open a remote
Windows resource such as the file and print server Oscar . From the Start
menu, select Run . Enter "\\oscar"
and press the OK button. After some amount of time, up to say 20
seconds, a window should open with the various file and printer shares
available on oscar. You should be able to navigate the files on oscar as
you would any Windows network server.
For some unexplained reason, the Windows resources on
the internal network may or may not appear when you browse the Network
Neighborhood.
After connecting to the PPTP server, all your IP traffic
is going to achille and onto the Bell Labs network; your machine is effectively
connect to the internal network and not to the Internet. One result of
this is that services that do not work inside the firewall, such as UDP,
will not work while you are connected to the PPTP server. Also, all connections
to the Internet will go via achille, with a potential reduction in performance.
If you want to directly connect to resources on the Internet, simply close
the PPTP connection to achille.